--------------------------------------------------------------------------- T H I S I S A D O C U M E N T I N A S C I I - F O R M A T ! ! ! --------------------------------------------------------------------------- To see the document in correct way under Windows 1. You must have installed a font with full ASCII-Character-Set (like TERMINAL) 2. Use a DOS-Editor like EDIT from original DOS-Version. EDIT filename.txt 3. Switch to DOS-Box and type in TYPE filename.txt | MORE 4. Switch to DOS-Box and print the file COPY filename.txt LPT1 TYPE filename.txt > LPT1 --------------------------------------------------------------------------- T H I S I S A D O C U M E N T I N A S C I I - F O R M A T ! ! ! --------------------------------------------------------------------------- ****************************************************************************** P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ****************************************************************************** 9 0 8 4 5 D 4 D I A M O N D M A X 4 3 MAXTOR Native³ Translation ÄÄÄÄÄÄÅÄÄÄÄÄÂÄÄÄÄÄÂÄÄÄÄÄ Form 3.5"/SLIMLINE Cylinders 13295³ ³ ³ Capacity form/unform 8455/ MB Heads 4³ ³ ³ Seek time í / track 9.0/ 0.9 ms Sector/track ³ ³ ³ Controller IDE / ATA4 ULTRA Precompensation Cache/Buffer 256 KB SDRAM Landing Zone Data transfer rate MB/S int Bytes/Sector 512 33.000 MB/S ext UDMA Recording method operating ³ non-operating ÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Supply voltage 5/12 V Temperature øC 5ö55 ³ -40ö71 Power: sleep 0.4 W Humidity % 5ö95 ³ 5ö95 standby 0.9 W Altitude km -0.061ö 3.048³ -0.061ö12.192 idle 4.1 W Shock g 20 ³ 200 seek 9.8 W Rotation RPM 5400 read/write 4.9 W Acoustic dBA spin-up 21.7 W ECC Bit MTBF h Warranty Month 36 Lift/Lock/Park YES Certificates P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** L A Y O U T ********************************************************************** MAXTOR 90845D4 JUMPER SETTING ÚÄÄÄÄÄÄÄÄÄÄÄ ÄÄÄÄÄÄÄÄÄÄÂÂÄÄÄÄÄÄÄÄÄÄÄÂÂÄÄÄÄÄÄÄÄÄ¿ ³ .................... ³³ Ü * * þ ³³ Û Û Û Û ³ ³ .......... ......... ³³ Ü þ þ þ þ ³³ Û Û Û Û ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÁÄÄÄÄÄÄÄÄÄÄÄÁÁÄÄÄÄÄÄÄÄÄÙ Interface Jumper Power P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** J U M P E R S ********************************************************************** MAXTOR 90845 JUMPER SETTING Jumper Setting ============== Pin 1 J1 IDE Connector ³ J2 Power ÚÄÄÄÄÄÄÄÄÄÄÄ ÄÄÄÄÄÄÄÄÅÄÂÂÄÄÄÄÄÄÄÄÄÄÄÂÂÄÄÄÄÄÄÄÄÄ¿ ³ .................... ³³ @ * * þ ³³ Û Û Û Û ³ ³ .......... ......... ³³ @ þ þ þ þ ³³ Û Û Û Û ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÁÄÂÄÂÄÂÄÂÄÂÄÁÁÄÂÄÂÄÂÄÂÄÙ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ J50 Master/Slave ÄÄÄÄÄÙ ³ ³ ³ ³ ³ ³ ³ ÀÄ+12V J48 Cable Select ÄÄÄÄÄÄÄÙ ³ ³ ³ ³ ³ ÀÄÄÄ+12V Return J46 4092 Cyl LimitationÄÄÄÙ ³ ³ ³ ÀÄÄÄÄÄ +5V Return J44 Factory Reserved ÄÄÄÄÄÄÄÙ ³ ÀÄÄÄÄÄÄÄ +5V J42 Factory Reserved ÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄ¿ ³J50³J48³J46³J44³J42³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄ´ ³ Master/Slave ³ ³ ³ ³ ³ ³ ³ Only Drive in single drive systemþ ³ J ³ ³ ³ ³ ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄ´ ³ Master in a dual drive systemþ ³ J ³ ³ ³ ³ ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄ´ ³ Slave in a dual drive system ³ O ³ ³ ³ ³ ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄ´ ³ Cable Select ³ ³ ³ ³ ³ ³ ³ Disabledþ ³ ³ O ³ ³ ³ ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄÅÄÄÄ´ ³ Enabled ³ ³ J ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÙ J=Jumpered O=Open þ=Default P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** I N S T A L L ********************************************************************** MAXTOR 90845D4 JUMPER SETTING Notes on installation ===================== Installation direction ---------------------- horizontally vertically ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³ ³ ³ ÃÄÄÄÄÄ¿ ÚÄÄÄÄÄ´ ³ ³ ³ ³ ³ ³ ³ ³ ³ ÚÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄ¿ ³ ³ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ÃÄÄÄÄÄÙ ÀÄÄÄÄÄ´ ³ ÀÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÙ ÀÄÄÙ ÀÄÄÙ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The drive will operate in all axis (6 directions). INSTALLATION PROCEDURE FOR AN IDE DRIVE --------------------------------------- 1. Install a 40 pin Data Cable ensuring that pin 1, which can be identified by the striped edge of the cable, is closest to the power connector on the drive. 2. Install a DC power cable to the back of the drive. 3. Verify the jumper configurations for Master/Slave operation (Note: Master will be the bootable drive. The slave will not be bootable.) Also make sure the existing C: drive is jumped to be the Master in a two drive system, not the only drive in the system. 4. Apply power to the computer. 4a. When memory test is complete go into your system's Standard CMOS set-up. (Note: There are various ways to get into CMOS set-up, please refer to system's manual for instructions.) 4b. If your system's BIOS supports a user programmable drive type, program the BIOS with the default parameters of your drive. If your system does not support a user programmable drive type choose parameters that closely match but do not exceed the drives MegaByte capacity. Escape from set-up then choose write to CMOS and exit. 5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on it. At the A> prompt type in FDISK. At the menu options select option 1 to create a DOS partition. Another menu will appear and from those options choose 1 to create a Primary DOS partition. Select yes to make 1 large partition and it will automatically become active. Then escape from FDISK. 6. At the A> prompt type in FORMAT C:/S This does a high-level format on the drive and transfers the system files in order for the drive to be bootable. (Note: IDE drives are low-level formatted from the manufacturer and only need a high-level format). To configure the drive as a slave drive repeat steps 1-4 and proceed with steps 5a. and 6a. as follows: 5a. At the C> prompt type in FDISK. When the menu options appear select option 5 to switch to the second drive. Enter fixed disk drive number 2. Then choose option 1 to create a DOS partition, then select option 1 again to create a Primary DOS partition or option 2 to create an Extended DOS partition. (Note: C and D drives will always be the Primary partitions but only the Primary partition on C: will have a status of active). 6a. Proceed with a high-level format on the drive by typing FORMAT D: (Note: Make sure the correct drive letter has been selected for format). 7. The drive is now bootable. As a test remove the DOS diskette from A and press reset to reboot the computer, a C> should be displayed, the drive is now ready for operation. P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** F E A T U R E S ********************************************************************** MAXTOR 90845D4 JUMPER SETTING Key Features: Exclusive Formula4 (TM) HDA ATA Power Saving commands Three-Year Warranty ANSI ATA4 Compliant PIO Mode 4 Interface Plus support for Ultra DMA/33 Mode 2 for up to 33 MBytes/sec. data transfers Supports EPA Energy Star "Green PC" Standards