--------------------------------------------------------------------------- T H I S I S A D O C U M E N T I N A S C I I - F O R M A T ! ! ! --------------------------------------------------------------------------- To see the document in correct way under Windows 1. You must have installed a font with full ASCII-Character-Set (like TERMINAL) 2. Use a DOS-Editor like EDIT from original DOS-Version. EDIT filename.txt 3. Switch to DOS-Box and type in TYPE filename.txt | MORE 4. Switch to DOS-Box and print the file COPY filename.txt LPT1 TYPE filename.txt > LPT1 --------------------------------------------------------------------------- T H I S I S A D O C U M E N T I N A S C I I - F O R M A T ! ! ! --------------------------------------------------------------------------- ****************************************************************************** P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ****************************************************************************** T R A V E L S T A R 1 0 G T 8 1 9 0 IBM Native³ Translation ÄÄÄÄÄÄÅÄÄÄÄÄÂÄÄÄÄÄÂÄÄÄÄÄ Form 2.5"/SUPERSLIMLINE Cylinders ³15880³ ³ Capacity form/unform 8190/ MB Heads ³ 16³ ³ Seek time í / track 12.0/ ms Sector/track ³ 63³ ³ Controller IDE / ATA ENHANCED Precompensation Cache/Buffer 460 KB SEGMENTED Landing Zone Data transfer rate 12.500 MB/S int Bytes/Sector 512 33.300 MB/S ext UDMA2 Recording method PRML operating ³ non-operating ÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Supply voltage 5 V Temperature øC 5ö55 ³ -40ö65 Power: sleep 0.1 W Humidity % 8ö90 ³ 5ö95 standby 0.3 W Altitude km -0.300ö 3.048³ -0.300ö12.192 idle 0.7 W Shock g 125 ³ 600 seek 2.3 W Rotation RPM 4200 read/write 2.1 W Acoustic dBA spin-up 4.7 W ECC Bit DFT ENABLED,SMART MTBF h Warranty Month Lift/Lock/Park YES Certificates P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** L A Y O U T ********************************************************************** IBM DCXA-210000/208100 TRAVELSTAR 10GT INSTALLATION GUIDE ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ ³ ³ ³ ÃÄÄÄÄÄÄÄÄInterfaceÄÄÄÄÄÄÄÄÄÄÄÄÄ49ÄÄÄÄÄÄ´ ³ 43þþþþþþþþþþþþþþþþþþþþþþ1 þþ47 Jumper ³ 44þþþþþþþþþþþþþxþþþþþþþþþ þþ48 ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ50ÄÄÄÄÄÄ´ À Ù Pin position 20 is left blank for correct connector insertion. Pin position 47 through 50 are used for drive address setting. P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** J U M P E R S ********************************************************************** IBM DCXA-210000/208100 TRAVELSTAR 10GT INSTALLATIONS Jumper Setting ============== Master/Slave Drive Address Setting ---------------------------------- A jumper is available at the interface connector to determine the drive address. ÄÄÄ49ÄÄ47¿ þ þ Û ³ Slave þ þ Û ³ ÄÄÄ50ÄÄ48Ù ÄÄÄ49ÄÄ47¿ þ þ þ ³ Master þ þ þ ³ ÄÄÄ50ÄÄ48Ù ÄÄÄ49ÄÄ47¿ þ þ þ ³ Cable Selection þ ÜÜÜ ³ ÄÄÄ50ÄÄ48Ù ÄÄÄ49ÄÄ47¿ þ ßßß ³ þ þ þ ³ RESERVED Never attach a jumper here! ÄÄÄ50ÄÄ48Ù ÄÄÄ49ÄÄ47¿ þ Û þ ³ NEVER ATTACH A JUMPER HERE!!! þ Û þ ³ ÄÄÄ50ÄÄ48Ù Cable Selection --------------- Using Cable Selection, the drive address depends on the condition of pin 28 of the AT interface cable. In the case when pin 28 is ground or low, the drive is a Master. If pin 28 is open or high level, the drive is a Slave. Cabling ------- The maximum cable length from the host system to the HDD plus circuit pattern in the host system shall not exceed 18 inches. AT Signal Connector ------------------- The AT signal connector is designed to mate with Dupont part number 69764-044 or equivalent. P C - D I S K The Harddisk Information Database DCI AG, Germany www.pc-disk.de ********************************************************************** I N S T A L L ********************************************************************** IBM DCXA-210000/208100 TRAVELSTAR 10GT JUMPER SETTINGS Notes on installation ===================== Installation direction ---------------------- horizontally vertically ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³ ³ ³ ÃÄÄÄÄÄ¿ ÚÄÄÄÄÄ´ ³ ³ ³ ³ ³ ³ ³ ³ ³ ÚÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄ¿ ³ ³ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ÃÄÄÄÄÄÙ ÀÄÄÄÄÄ´ ³ ÀÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÙ ÀÄÄÙ ÀÄÄÙ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The drive will operate in all axis (6 directions). Performance and error rate will stay within specification limits if the drive is operated in the other permissible orientations from which it was formatted. Thus a drive formatted in a horizontal orientation will be able to run vertically and vice versa. The drive must be securely mounted in the system to prevent motion or vibration during a seek operation or spindle rotation using appropriate screws or equivalent mounting hardware. The recommended mounting screw torque is 3.0 ñ 0.5 kgf.cm. The recommended mounting screw depth is 3.0 ñ 0.3mm for bottom and 3.5 ñ 0.5mm for horizontal mounting. Air Cooling Requirement ----------------------- The host system must provide sufficient air flow across the drive to maintain the temperature at less than 60øC (measured at the centre of the files top cover).